MATERIAL SAFETY DATA SHEET

I. PRODUCT IDENTIFICATION

Manufacturer/Supplier:

ESPI Metals

1050 Benson Way, Ashland, OR 97520

Toll Free (800) 638-2581 * Fax (541) 488-8313

E-Mail: sales@espimetals.com

Trade Name:                    Graphite

Chemical Family:             Carbon

CAS #:                               7782-42-5

Formula:                           C₆

II. HAZARDOUS INGREDIENTS

Hazardous Component:  Graphite

%:                                     0-100

OSHA/PEL:                     5 mg/m³

ACGIH/TLV:                   10 mg/m³

III. PHYSICAL DATA

Boiling Point:                   Not determined

Melting Point/Range:      3652 - 3697 ^oC

Specific Gravity:              2.0 g/cc

Vapor Pressure                N/A

% Volatiles:                      N/A

Solubility in H₂O:            Insoluble

Appearance and Odor:    Steel grey to black, no odor.

Molecular Weight:           12.01

IV. FIRE AND EXPLOSION HAZARDS DATA

Flash Point: N/A

Autoignition Temperature: N/A

Flammable Limits: Lower: N/A  Upper: N/A

Extinguishing Media: Use suitable extinguishing media for surrounding material and type of fire.

Special Fire Fighting Procedures: Firefighters must wear full face, self-contained breathing apparatus with full protective clothing to prevent contact with skin and eyes.

Unusual Fire & Explosion Hazard: None

V. HEALTH HAZARD INFORMATION

Effects of Exposure:

Acute Effects:

Inhalation: Breathing dusts may result in aggravation of existing respiratory diseases.

Ingestion: None known

Skin: None known

Eye: May be irritating to the eyes.

Chronic Effects: Overexposure to respirable dust from machining/crushing may aggravate existing respiratory diseases. Massive overexposure may cause pneumoconiosis.

EMERGENCY AND FIRST AID PROCEDURES:

INHALATION: If irritation of the nose and throat occurs from exposure to dusts, move away from exposure and into fresh air. If irritation persists, seek medical attention. If victim is not breathing or if breathing difficulties develop artificial respiration or oxygen should be administered by qualified personnel. Seek medical attention.

INGESTION: If victim is conscious and alert, give 2 to 3 cups of milk or water to drink. Seek medical attention.

SKIN: No first aid is normally required but if irritation or redness develop from exposure to dusts, remove contaminated clothing and flush the affected area(s) with large quantities of clean water. If the effects persist, seek medical attention.

EYE: For contact with dusts, flush the affected eye(s) with clean water. If irritation or redness develop, seek medical attention.

VI. REACTIVITY DATA

Stability: Stable

Conditions to Avoid: None

Incompatibility (Material to Avoid): Avoid contact with strong oxidizing agents.

Hazardous Decomposition Products: CO, CO₂ evolved when exposed to O₂ at temperatures above 500 ^oC.

Hazardous Polymerization: Will not occur.

VII. SPILL OR LEAK PROCEDURES

Steps to be Taken in Case Material is Released or Spilled: Turn off ignition sources. Remove by mechanical means and place material in metal container temporarily for later disposal. Clean-up procedure should insure minimizing dust; vacuum dust instead of sweep, for example.

Waste Disposal Method: In accordance with Local, State and Federal Waste Disposal Regulations.

VIII. SPECIAL PROTECTION INFORMATION

Respiratory Protection (Specify Type): Wear NIOSH approved respirator for nuisance dust when crushing or machining.

Ventilation: Use local exhaust to maintain concentrations at or below PEL, TLV. General exhaust is recommended.

Protective Gloves: Not normally required. If dusts are expected to be generated, the use of protective gloves is advised to prevent skin contact and possible irritation.

Eye Protection: Safety glasses

IX. SPECIAL PRECAUTIONS

Work Practices: Implement engineering and work practice controls to reduce and maintain concentration of exposure. Use good housekeeping and sanitation practices. Do not use tobacco or food in work area. Wash thoroughly before eating or smoking. Do not blow dust off clothing or skin with compressed air. Maintain eyewash capable of sustained flushing, safety drench shower and facilities for washing.

DOT Regulations:

(Fine Powder)

Hazard Class:                   4.1                                                    

Identification Number:    UN1325

Packing Group:                III                                                     

Proper Shipping Name:   Flammable solid, organic, n.o.s., (graphite)

(Solid forms are not regulated)

The above information is believed to be correct, but does not purport to be all inclusive and shall be used only as a guide. ESPI shall not be held liable for any damages resulting from handling or from contact with the above product.

Issued by:            S. Dierks

Date:                    November 2005